• Phone orders: +48 22 464 86 86
  • Have a question? shop@diabetic24.com
waterproof insulin pump case

waterproof insulin pump case

Aquapac
707398111584
In Stock
52.65

Description

Key Features

  • Use all buttons and switches through the case
  • Also protects from dust, dirt and sand
  • Supplied with a belt, or you can use your own belt
  • Like most of our cases it’ll float if you drop it in the drink
  • The seams are high-frequency welded to form a super-strong bond
  • This case features our ‘TC’ Aquaclip which makes the case waterproof to IPX6. Temporary immersion is fine, but not continuous immersion (see below for more).

What size do I need?

The case works with most insulin infusion pumps.

Tip: to get the circumference, add the width to the depth and then multiply this by 2

How waterproof is it?

IPX6 waterproofing levelIt’s Stormproof (protected against powerful water jets – click on the icon for more)

But can I swim with it?

Although it’s not designated as Submersible we have had reports from many, many users that in practice they or their children have enjoyed swimming with our cases with no problem whatsoever (the vast majority of our customers have bought the case for their children). We are talking here about splashing around in the pool or the sea, but we are NOT talking about endurance/long-distance swimming. Our testing shows that the TC clamp will let a tiny amount of water in after a period of total immersion. So the best advice we can give is to wear it in the small of your back if you’re swimming on your front, and on your tummy if you’re swimming on your back, so that it spends as little time submerged as possible.

PVC-Free

Colour

Cool grey with grey belt

Materials

300mu UV-resistant TPU

Weight

Case: 1.7oz / 47g  Belt: 2.1oz / 59g

Country of Origin

Made in the UK.

Important Note regarding Insulin Pumps and Aquapac cases

Aquapac commissioned research by Imperial College London into the suitability of their cases for use with insulin pumps. Results show that in some circumstances insulin flow rate can be reduced by the case. In particular, low flow rates are impeded and as such Aquapac can make no claim regarding the suitability of these cases with insulin pumps. Use of these cases with insulin pumps is entirely at the discretion of the user.

We are advised to recommend that users of Aquapac cases with insulin pumps regularly check their blood sugar levels. Furthermore we strongly recommend that you get the green light from your consultant before use.

The tests were conducted by Imperial College of Science, Technology and Medicine using a Roche Accu-Check Spirit insulin pump at a temperature of 20C at flow rates of 2U/hr and 10U/hr. The amounts of insulin delivered over 60 minutes observed were as follows:

2U/hr not in a case – 0.0131g (flow rate of 100%)

2U/hr in Aquapac 150 – 0.0106g (flow rate of 81%)

2U/hr in Aquapac 150 – 0.0056g (2nd test model)(flow rate of 42%)

2U/hr in Aquapac 550 – 0.0121g (flow rate 92%)

10U/hr not in case – 0.0864g (flow rate of 100%)

10U/hr in Aquapac 150 – 0.0878g (flow rate of 100%)

10U/hr in Aquapac 550 – 0.0903g (flow rate of 100%)

21st August 2006

Special Instructions for the ‘TC’ Clamp

To Open

instructions diagram

click to expand

Flip the two levers up, one at a time.

Twist the two levers out.

To Close

Place the wire or tube carefully under the retaining arm. The wire/tube must exit through the groove in the clamp.

Place the two halves of the clamp back together so that the wire is held gently in place. Do not squeeze them together hard.

Twist both the levers in, one at a time. Twist both levers before attempting step 6.

Flip the levers over to seal the clamp.

Important Notes

Cases with this clamp are for surface use only, but will offer protection from temporary submersion. They are not recommended for prolonged submersion.

When not using the case leave the TC clamp open. If not the wire or tube could eventually cause a permanent distortion of the foam, risking leakage.

As long as you follow this instruction the clamp will be watertight with or without a wire/tube.

The maximum thickness of wire/tube around which the TC clamp will seal is 1/10th inch (2.5mm).

(code 158A)

Shipping, courier:
  • Austria
    2-6 days€ 11.00
  • Belgium
    2-6 days€ 11.00
  • Bulgaria
    2-6 days€ 15.00
  • Croatia
    2-6 days€ 13.00
  • Cyprus
    2-6 days€ 75.00
  • Czech Republic
    2-6 days€ 10.00
  • Estonia
    2-6 days€ 13.00
  • Finland
    2-6 days€ 13.00
  • France, Metropolitan
    2-6 days€ 15.00
  • Greece
    2-6 days€ 24.00
  • Hungary
    2-6 days€ 12.00
  • Italy
    2-6 days€ 15.00
  • Latvia
    2-6 days€ 15.00
  • Lithuania
    2-6 days€ 12.00
  • Luxembourg
    2-6 days€ 12.00
  • Malta
    2-6 days€ 75.00
  • Netherlands
    2-6 days€ 12.00
  • Polska
    2-6 days€ 10.00
  • Portugal
    2-6 days€ 15.00
  • Romania
    2-6 days€ 15.00
  • Slovak Republic
    2-6 days€ 10.00
  • Slovenia
    2-6 days€ 12.00
  • Spain
    2-6 days€ 15.00
  • Sweden
    2-6 days€ 15.00
ANY QUESTIONS?: +48 22 464 86 86